DSpace Home
→
PG Thesis
→
Computer Integrated Manufacturing (CIM)
→
Browsing Computer Integrated Manufacturing (CIM) by Issue Date

Browsing Computer Integrated Manufacturing (CIM) by Issue Date

Now showing items 1-20 of 26

DEVELOPMENT OF VEGETABLE OIL BASED NANO CUTTING FLUID- EXPERIMENTAL STUDY AND PERFORMANCE EVALUATION.

Anurag, P; Krishnakumar, T S (2022-07)

Cutting fluids, used in manufacturing process as coolant and lubricant, are currently based on mineral oils which are depleting and non-eco-friendly. A good replacement is vegetable oil based cutting fluids which are ...
INVESTIGATIONS OF DIRECT SUNLIGHT CURING OVER ARTIFICIAL UV CURING OF COMPOSITES FOR STRUCTURAL APPLICATIONS.

Febin, Geo Sam; Mubarak, Ali (2022-07-07)

Current world scenarios demand the need of making fabrication more sustainable with renewable energy sources as it plays a vital role in global sustainability. The technological and scientific advancement along with ...
EXPERIMENTAL INVESTIGATION AND OPTIMIZATION OF CUTTING PARAMETERS IN HARD TURNING OPERATION

Muhammed Bukhari, B N; Kannan, S (2022-09-12)

The need for materials with extraordinary characteristics is one of the major challenges faced by the engineering sector. This project takes an alternative strategy since it addresses the economic impact on pure hard ...
COMPARISON OF TRIBOLOGICAL BEHAVIOUR OF ALUMINIUM BORON CARBIDE AND COCONUT SHELL ASH COMPOSITES

Midhun, A R; Rakesh Pillai, R (2022-09-12)

Composite materials became the cornerstones in Material Science and Technology spanning the last two decades. Improved performance with the introduction of affordable manufacturing techniques made composite materials ...
EXPERIMENTAL OPTIMIZATION OF ABS CONTENT IN PC FOR ENHANCED SYNERGISM EFFECT OF PC/ABS BLEND IN CFRP COMPOSITES WITH ENHANCED FRACTURE TOUGHNESS

Kasthoori, M S; Reby Roy, K E (2022-09-12)

Thermoplastic modification of Bisphenol A diglycidyl ether (DGEBA epoxy resin) is commonly performed for achieving enhanced fracture toughness and increased interlaminar strength in carbon fiber reinforced polymer ...
AN INVESTIGATION INTO THE EFFECT OF COMPACTION ON THE PERFORMANCE OF COMPOSITE MATERIAL MADE FROM WATER HYACINTH AND RICE STRAW

Anandhu, Krishanan G; Shafi, K A (2022-09-12)

The conversion of biomass waste resources into value-added products is gaining popularity on a wide range all over the world. Thermal insulation materials derived from agricultural and aquatic waste are becoming more ...
EXPERIMENTAL INVESTIGATION ON MECHANICAL PROPERTIES OF UNTREATED AND CRYO-TREATED HEMP FIBER REINFORCED POLYMER COMPOSITES

Renju, C Daniel; Mubarak, Ali (2022-09-12)

Emerging research is primarily concerned with environmental and economic challenges associated with the development of new materials for future industries. Various industry sectors have been attempting to replace ...
SUSTAINABLE DEVELOPMENT AND DESIGN OPTIMIZATION OF HYBRID PLASTIC ROOFING TILE COMPOSITES FOR ENHANCED REDUCTION OF THERMAL LOAD

Kasthoori, Nath A J; Reby Roy, K E (2022-09-12)

The novel ‘plastile’ composite roofing tiles (8 × 8 × 1.3 cm3) are prepared using a three-step controlled compression process. The developed tiles are having an inner core section of metal oxide layer encased by the ...
MECHANICAL INVESTIGATION OF CRYO-TREATED SILANIZED GRAPHENE OXIDE MODIFIED CARBON FIBER REINFORCED POLYMER COMPOSITE

Rajalekshmi, S; Reby Roy, K E (2022-09-12)

The Space industry is still in search for a suitable material for cryogenic tanks. Carbon Fiber Reinforced Plastic composites is identified as a compatible material for cryogenic applications. Various researches are ...
ANALYSIS OF MAGNETIC FLUX, DYNAMIC VISCOCITY AND YIELD STRESS DISTRIBUTION IN MR DAMPER

Adhil, Mohammed .A; Rizwan, Rasheed (2022-09-12)

Magnetorheological materials are smart materials where its rheological characteristics can be quickly changed by the introduction of a magnetic field. The electromagnet and a piston submerged in an MR fluid make up the ...
PREDICTION OF STRESS GENERATED AT INSOLE SUB-SYSTEM OF DIABETIC FOOT ULCER OFFLOADING DEVICE USING FULL FACTORIAL DOE

Nameer, Najeeb; Kannan, S (2022-09-16)

Diabetes is one of the metabolic diseses.Uncontrolled diabetes can lead to diabetic foot ulcers and if it is not treated further it would lead to amputation. Foot ulcer patients are prescribed with Diabetic Foot Ulcer ...
EXPERIMENTAL INVESTIGATION ON THE PHYSICAL AND COMBUSTION PROPERTIES OF BRIQUETTES FROM VARIOUS AGRO -AQUATIC WASTES

Sonu, S; Shafi, K A (2022-09-16)

The constant increase in environmental pollution and depletion of renewable resources leads to a focus on bio briquette. Therefore, several issues arise relating to reusing or recycling such materials. Many of the ...
Experimental Investigation and Optimization of PC/ABS Blend Composition in DGEBA Resin for Resin Infusion Moulding(RIM)

Anukrishna, G S; Kannan, S (2023-07)

This research investigates the issue of brittleness in DGEBA resin, which limits its suitability for aerospace composite materials. The study explores the combined effects of polycarbonate (PC) and acrylonitrile butadiene ...
CFD-Analysis Study of Drug Deposition In Tracheobronchial Airways of Asthmatic Persons From Different Age Groups

Praful, P; Kannan, S (2023-07)

The people who already had respiratory conditions like asthma were the ones who suffered the most from COVID.The most frequent chronic illness in children, asthma, is the main factor in pediatric hospitalizations all ...
EFFECT OF CRYOTREATMENT ON THE MICROSTRUCTURAL EVOLUTION OF Ti-Al-Ni-Cr-Co-Fe BASED HIGH ENTROPY ALLOY

Arjun, Santhosh; Kannan, S (2023-07-07)

High Entropy Alloys (HEAs) are new class of materials. Recent Studies on HEAs have attracted much attention in the field of scientific research and industry. There has been a lot of interest in HEA compositions having ...
EVALUATION OF MICROSTRUCTURE, MECHANICAL, AND CORROSIVE BEHAVIOUR OF ALUMINIUM METAL MATRIX COMPOSIT

Akhil, H; Kannan, S (2023-07-11)

The aim of this research project is to examine the results of using stir casting to incorporate boron carbide (B4C) and coconut shell ash as reinforcements into an Al1350 alloy (aluminium wire) matrix. To improve its ...
PATIENT SPECIFIC DESIGN AND FEA BASED OPTIMIZATION OF ANKLE FOOT ORTHOSI

Milan, M; Kannan, S (2023-07-11)

The digital workflow in orthotics and Prosthetics is the use of digital technology and tools to simplify and streamline the fabrication process of a prosthetics or an orthosis. There are a significant range of digital ...
DEVELOPMENT OF SMART DIABETIC FOOT WALKER – PROOF OF PRINCIPLE PHASE

Anverlal, A N (2023-07-12)

Biomechanics studies usually limited to resource intensive laboratory with relevant technical expertise. The biomechanical assessments help to identify, understand and give treatments for disorders and diseases affecting ...
DISSIMILAR METAL WELDING OF INCONEL 718 WITH TI6AL4V: A SIMULATION-BASED APPROACH USING CATIA

Arun, K S; Kannan, S (2023-07-12)

Dissimilar metal welding, particularly the joining of Inconel 718 and Ti-6Al-4V alloys, presents significant challenges due to their disparate properties. This study proposes a simulation-based approach for Tungsten ...
NEURAL NETWORK-BASED PREDICTION OF MODIFIED CFRP COMPOSITES USED IN AEROSPACE APPLICATION

Mohammed, Sanal B; Kannan, S (2023-07-12)

CFRPs, or carbon fiber reinforced polymers, are renowned for having superior wear characteristics. In this study, we compared the wear properties of polycar bonate (PC)/acrylonitrile butadiene styrene (ABS) modified ...

Now showing items 1-20 of 26

Search DSpace

Advanced Search

Browse

All of DSpace
This Community
- By Issue Date
- Authors
- Titles
- Subjects

Browsing Computer Integrated Manufacturing (CIM) by Issue Date

Browsing Computer Integrated Manufacturing (CIM) by Issue Date

Search DSpace

Browse

All of DSpace

This Community

My Account